udjes u GLOBAL i tamo ces naci sto trazis...
Evo i uputstva kako resetovati na fabricka podesavanja za neke KORG klavijature:
<table class="table01" x:str="" border="1" cellpadding="5" cellspacing="1" width="465"><tbody><tr height="17"><td bordercolor="#66ffff" align="center" bgcolor="#66ffff" height="17" valign="middle" width="64">
Product</td> <td align="center" bgcolor="#66ffff" valign="middle" width="716">
Preload Instructions
</td> </tr> <tr height="17"> <td height="17">01/W Series</td> <td>Global screen 7 Press G then E</td> </tr> <tr height="17"> <td height="17">03R/W</td> <td>Global screen 5D, then select “OK”.</td> </tr> <tr height="17"> <td height="17">05R/W</td> <td>Global Screen 5A, then select “OK”.</td> </tr> <tr height="17"> <td height="17">168RC</td> <td>Factory data must be transmitted and returned via SysEx dump.</td> </tr> <tr height="17"> <td height="17">A1</td> <td>Card Load only from a SPC0A1 (Card no longer available)</td> </tr> <tr height="17"> <td height="17">A2/A3</td> <td>Hold Up and Down arrows while turning it on.</td> </tr> <tr height="17"> <td height="17">A4</td> <td>Hold Bank Up and Write while turning it on. PL appears, press write again.</td> </tr> <tr height="17"> <td height="17">A5</td> <td>Hold Mode Footswitch and Write while turning it on. Press Footswtich 1, F is dispayed on screen.</td> </tr> <tr height="17"> <td height="17">AD120VT</td> <td>Preload - Hold down the value Up/Down button and TUNER/CANCELL. A 'P' will flash in the LED. Press the write button</td> </tr> <tr height="17"> <td height="17">AX1000G</td> <td>Hold Bank footswitch and Exit button while turning it on. Press Write button to load the factory programs. </td> </tr> <tr height="17"> <td height="17">AX100G</td> <td>Hold FX Select and EXIT button while turning it on. Press write button. </td> </tr> <tr height="17"> <td height="17">AX1500G</td> <td>Hold down Bank footswitch EXIT button while turning it on. Then press Write button.</td> </tr> <tr height="17"> <td height="17">AX1G/B</td> <td>Hold down the left arrow key and the "+ " while powering on. Then press the "+" button again.</td> </tr> <tr height="17"> <td height="17">AX300G/B</td> <td>Hold Param/Value and Compare/Write while turning it on. Then Compare/Write once again.</td> </tr> <tr height="17"> <td height="17">C-Series</td> <td>Disk Load C900 (CFD01P) Ci86/9600 (CID00PE )</td> </tr> <tr height="17"> <td x:str="CX-3 " height="17">CX-3 </td> <td>Hold Program 2 and 7 while turning it on.</td> </tr> <tr height="17"> <td height="17">D Series</td> <td>Backup CDs</td> </tr> <tr height="17"> <td height="17">EX8000</td> <td> From Tape only (Contact us via the support form for more information)
</td> </tr> <tr height="17"> <td height="17">G3</td> <td>Hold Bank and Write while turning it on. Release both and then press Write again.</td> </tr> <tr height="17"> <td height="17">i1/i2/i3</td> <td>Disk Load (IFD01P for i3 and i2, IFD02P for i1)</td> </tr> <tr height="17"> <td height="17">I30</td> <td>Disk Load (I30FD00P)</td> </tr> <tr height="17"> <td height="17">i5S/M</td> <td>Disk Load (IFD00P)</td> </tr> <tr height="17"> <td height="17">iS35/40/50/B i40M</td> <td>Disk Load (IFDD1006 except for iS40 and i40M which is IFDD1007)</td> </tr> <tr height="17"> <td height="17">iX300</td> <td>Disk Load (IXD00P)</td> </tr> <tr height="17"> <td height="17">KAOSS Pad</td> <td>N/A</td> </tr> <tr height="17"> <td height="17">KARMA</td> <td>Disk Load (KMFD00P)</td> </tr> <tr height="17"> <td height="17">M1</td> <td>Card Load (MPC00P) or Sysex Dump. Please contact support for information on how to send data via Sysex. (Card no longer available)</td> </tr> <tr height="17"> <td height="17">M1R/M1REX</td> <td>Card Load (MPC00P, MPC0EX for EX model, no longer available)</td> </tr> <tr height="17"> <td height="17">M3R</td> <td>Global screen 5D “OK”, then select "OK."</td> </tr> <tr height="17"> <td height="17">MS2000/2000R</td> <td>Global screen 2D, then select "OK".</td> </tr> <tr height="17"> <td height="17">N1/N5/EX</td> <td>Press Utility, select "Factory Reset" then press Enter.</td> </tr> <tr height="17"> <td height="17">N1R</td> <td>Press Global, Page > to Init. Select "Factory Preload" then press Enter.</td> </tr> <tr height="17"> <td height="17">N364/N264</td> <td>Disk Load (NSD3)</td> </tr> <tr height="17"> <td height="17">NX/NS5R</td> <td>Enter button, then select Utility, Preset, Factory Preset, Yes.</td> </tr> <tr height="17"> <td height="17">PA80/60</td> <td>Disk Load (6 Disk set available from
www.korgpa.com)</td> </tr> <tr height="17"> <td height="17">Prophecy</td> <td>Global screen 19, press Enter.</td> </tr> <tr height="17"> <td height="17">PX1</td> <td>Metronome and Enter buttons while powering on. Then press the "+" button.</td> </tr> <tr height="17"> <td height="17">PX2</td> <td>Rhythm and Enter buttons while powering on. Then press the "+" button.</td> </tr> <tr height="17"> <td height="17">PX3/PX3B</td> <td>PX3: Rhythm/Aux and "+" button while powering on. Then press the Bypass/Tune button. PX3B: HBB and "+" button while powering on. Then press Bypass/Tune.</td> </tr> <tr height="17"> <td height="17">PX4/PX4B</td> <td>PX4: Rhythm and UP arrow buttons while powering on. Then press Enter/Rec. PX4B: Rhythm and Up arrow buttons while powering up. Then press press Enter/Rec.</td> </tr> <tr height="17"> <td height="17">S3</td> <td>Hold Stop and S1 while turning it on.</td> </tr> <tr height="17"> <td height="17">SG Rack</td> <td>Global screen 7, then select "OK".</td> </tr> <tr height="17"> <td height="17">SGPROX</td> <td>Program Edit mode screen 14 (Each program!)</td> </tr> <tr height="17"> <td height="17">SP500</td> <td>Function screen 7.</td> </tr> <tr height="17"> <td height="17">T Series</td> <td>Disk Load (TSD00PII)</td> </tr> <tr height="17"> <td height="17">Trinity Series</td> <td>Disk Load (TFD00P and TFD01P)</td> </tr> <tr height="17"> <td height="17">Triton Classic/ST</td> <td>Disk Load (TNFD00P and TNFD01P for Classic, Hard Drive contains preload for Studio)</td> </tr> <tr height="17"> <td height="17">Triton LE</td> <td>Global mode, F8, Select "Preload" then OK</td> </tr> <tr height="17"> <td height="17">Triton Rack</td> <td>Disk Load (TNRFD00P and TNRFD01P)</td> </tr> <tr height="17"> <td height="17">TR Rack</td> <td>Global screen 10, then select "OK".</td> </tr> <tr height="17"> <td height="17">WS/WSEX/AD</td> <td>Card Load (WPC00PI, II and III)</td> </tr> <tr height="17"> <td height="17">WSSR</td> <td>Card Load (WPC00PI, II and III)</td> </tr> <tr height="17"> <td height="17">X2/X3/X3R</td> <td>Disk Load (XSD00P)</td> </tr> <tr height="17"> <td height="17">X5/X5D/DR</td> <td>Global Screen 5A, then select “OK”.</td> </tr> <tr height="17"> <td height="17">Z1/Z1EX</td> <td>Preload screen in global mode.</td></tr></tbody></table>
